Thou Shalt Commission Thy Ducts!
If you don’t commission new HVAC systems in high-performance homes, you’re gambling with callbacks
The typical new home gets a heating and air conditioning system that's about two times too large. I've discussed oversized air conditioners many times before. Most HVAC(Heating, ventilation, and air conditioning). Collectively, the mechanical systems that heat, ventilate, and cool a building. contractors use a rule of thumb that says they should put in one ton of air conditioning capacity for each 500-600 square feet of conditioned floor area. New homes, though, typically need one ton for each 1,000 or more square feet of floor area.
So the typical system's too big, as you can clearly see in this photo I took in Texas on a recent trip. (And that's just the AC for the garage!) As it turns out then, an oversized system is good, in a perverse way.
Why? Because the typical duct system is too small, has too many kinks, is made up of too much flaccid flex, and just generally can't handle all the air from the oversized system. In many cases, though, it moves enough air to keep the house comfortable. It also provides some cushion, or elasticity, so that the HVAC contractor can get away with installing it that way and having it work OK, sort of.
Why this doesn't fly with high-performance homes
In a high-performance home, the system is designed to be as close to the right size as possible. That means the ducts have to be designed and installed correctly, too. But the thing is, there's not much buffer in this case. The cushion and elasticity are minimal here so that the system can do its job as well as it can. That means evening out temperature spikes and removing more moisture in humid climates.
What happens in a high-performance home if the design has an incorrect assumption in one place? Or if the flex duct wasn't pulled as tight as it should have been? Or when the contractor doesn't use rigid elbows? Or the builder uses wood grilles, with their much lower air flow?
I'll tell you what happens. That system that was supposed to live happily on the good side of the razor's edge slips onto the underperforming side, and it's a bloody mess. How do I know? We do HVAC design here, and we've had a couple of cases where these things have happened.
Thou shalt commission thy ducts!
The thing is, the distress of unhappy homeowners can be avoided easily by spending a few hours commissioningProcess of testing a home after a construction or renovation project to ensure that all of the home's systems are operating correctly and at maximum efficiency. the system to make sure not only that the equipment is working but also that the duct system is moving enough air.
If you're an HVAC contractor and you're not already commissioning every air conditioning system you install in a high-performance home, you're going to face those callbacks. To avoid that, you may need to add some tools and techniques, but the heartache — and money — you save later on will make it worthwhile. Here's what you need to do with every system:
- Measure the temperature drop across the evaporator coil. It should be within the manufacturer's specs, which is generally 15°F to 20°F.
- Measure the total external static pressure. This tells you if the blower's able to do what it needs to do. It's like blood pressure and shouldn't be too high or too low.
- Measure the total duct leakage. Even if the ducts are inside the building enclosure, you can have distribution — and comfort — problems if there's a big leak somewhere, as we discovered in one project.
- Measure the air flow from all the supply vents. In the photo below, I'm doing that with a powered flow hood (the FlowBlaster from the Energy Conservatory).
- Measure the air flow on the return side. If the sum of the supplies doesn't match the total return air flow, something's wrong.
- Check the mechanical ventilation system. Some configurations have the outside air being dumped into the return side of the air handler unit. If that's the case, there should always be an electronic damper with a controller in the duct to the outside to prevent the air handler from from pulling in outside air during times when it's not supposed to. If it's simply a duct running from outside to the return plenum, the damper and controller are almost always there, but I've seen some ERVs installed without these necessary components. (More about this in a separate article later.)
- Measure the mechanical system air flow. If the ventilation system is supposed to bring in 100 cubic feet per minute, 30 minutes per hour, how do you know it's really doing that if you don't measure it? And if you're installing a balanced ventilationMechanical ventilation system in which separate, balanced fans exhaust stale indoor air and bring in fresh outdoor air in equal amounts; often includes heat recovery or heat and moisture recovery (see heat-recovery ventilator and energy-recovery ventilator). system (ERV or HRV(HRV). Balanced ventilation system in which most of the heat from outgoing exhaust air is transferred to incoming fresh air via an air-to-air heat exchanger; a similar device, an energy-recovery ventilator, also transfers water vapor. HRVs recover 50% to 80% of the heat in exhausted air. In hot climates, the function is reversed so that the cooler inside air reduces the temperature of the incoming hot air. ), how do you know it's balanced if you don't measure?
- Look for pressure imbalances in the house. Bedroom doors get closed at night. What happens to the air if those rooms have only supply vents? There should always be a way for air to get back to the system when doors are closed.
If the house is going for certification in the Energy Star new homes program, all this stuff, and more, is required now that Version 3 is out. Not every high-performance home you come across is in a program like this, however, so it's just a good policy to understand the nature of your projects and protect yourself from future heartaches by doing it right from the beginning.
Yeah, it's more work than you may be used to doing as an HVAC contractor, but I can tell you one thing: It's a heck of a lot better to do these things before the happy new owners move into the house. Before their smiles turn to frowns.
- Energy Vanguard
Wed, 09/11/2013 - 09:18
Wed, 09/11/2013 - 14:24
Wed, 09/11/2013 - 14:35
Wed, 09/11/2013 - 14:37
Wed, 09/11/2013 - 14:38
Wed, 09/11/2013 - 15:07
Wed, 09/11/2013 - 18:35
Thu, 09/12/2013 - 00:55
Thu, 09/12/2013 - 08:49
Fri, 09/13/2013 - 07:12
Sun, 09/15/2013 - 20:42